Optec Venum TLSO Back Support With Dorsal Lumber Kit

Optec Venum TLSO Back Support With Dorsal Lumber Kit

Brand/Manufacturer: OPTEC USA
Save
Authorized Retailer Badge
  • FSA Approved

Optec Venum TLSO Back Support With Dorsal Lumber Kit features an innovative single drawstring pulley closure system to increase support and compression with minimal effort from sacrococcygeal junction to the thoracic inferior scapular spine. The lightweight mesh and ergonomic design with anterior and posterior panels provide sagittal control and intracavitary compression. The Venum TLSO rigid panels contour to the patient’s lordotic curve and abdomen resulting in comfort, control and increased compliance.

Item # Desc Pkg Price
VIPTLDLKSM Small Each
$498.99
$369.66
VIPTLDLKMD Medium Each
$498.99
$369.66
VIPTLDLKLG Large Each
$498.99
$369.66
VIPTLDLKXL X-Large Each
$498.99
$369.66
VIPTLDLK2X 2X-Large Each
$498.99
$369.66
VIPTLDLK3X 3X-Large Each
$498.99
$369.66

Optec Venum TLSO Back Support Features

  • Indicated for:
    - Burst FX
    - Compression FX
    - Post-op spinal lumbar stabilization
    - Post-op disk surgery
    - Chronic back pain
    - Degenerative, herniated or bulging disc
    - Spondylolysis
    - Spondylolisthesis
    - Spinal stenosis
    - Facet syndrome
    - Tumors or inflammation
    - Spinal instability
    - Post-op laminectomy
  • Standard components:
    - Post-op immobilization polymer panel
    - 2 lateral polymer panel
    - Anterior polymer panel
    - Dorsal lumber kit (DLK)

More On Optec Venum TLSO Back Support

Important to know:
  • Mechanical advantage pulley system requires that you place handle next to Power Units and have product fully open (cords extended) each time you put it on to maximize support.
  • Placement around low back is critical to ensure proper support.
  • Power units must be centered on spine when fully extended.
  • Experiment with different locations to determine best support in different positions.
  • Product can be worn over or between clothing.

Instructions for use:
  • Open and extend the panels. The panels should be fully extended each time it is applied. The panel with the handle should be on the left. Center the two ends of the pulley device on the posterior panel.
  • Wrap the sides around the abdomen with the right side overlapping the left side.
  • Pull the handle to the desired position. When the appropriate amount of tension is reached, place the hook backed handle down on the loop strip of the corset to secure.

User Tips:
  • Pull handle only slightly at first, until you get used to the power.
  • Tighten to stand, loosen to sit. You control the tension.
  • Practice with the product on, to determine positions you use every day.
  • Pulling in stomach muscles before tightening makes pulling handle easier.
  • Do not wear tight for long periods of time unless instructed by physician.
  • The product was designed to enable adjustment throughout the day to provide real support when you need it and less support when you don’t.
  • To disconnect Power Units, slide Power Units outward on side panels. To reattach, reverse the process. Power Unit slides on and off of metal post.
  • Hand wash in warm water, towel off, and air dry in shade.

Optec Venum TLSO Back Support Specifications

Size Waist Measurement
Small 25" to 30"
Medium 30" to 35"
Large 35" to 40"
X-Large 40" to 45"
2X-Large 45" to 50"
3X-Large 50" to 55"

Warranty

The warranty on the VENUM is free repair or replacement for manufacturers defects within 6 months of the date fitted.

Customer Reviews

Please enter your and your friends email address below.
Fields marked with * are compulsory
 
*
*
*
*


Submit Cancel
The selected product information has been successfully emailed to your friend.

Thank you for using www.rehab-store.com

Close