Moog EnteraLite Infinity Enteral Feeding Pump

How to use Moog EnteraLite Infinity Enteral Feeding Pump?

• Dale ACE Connector
• Medline Enteral Feeding and Irrigation Syringe

Also available (separately):

• Nestle EnteraLite Infinity Mini Backpack (Code PCK1001)

How to use Moog EnteraLite Infinity Enteral Feeding Pump?

1. If you are using the Safety Screw Connector or Spike set with a vented bottle or pre-filled bag, remove the protective cover from the tip, then insert the tip into the formula exit port of the container. If using the Safety Screw Connector set, secure the tip by tightly screwing threaded components together. If you are using the 500ml or 1200ml disposable set, hold the bag upright and pour in the enteral feeding solution. Then, close the cap securely.
   NOTE: Blenderized or aggressively mixed solutions may have foam. If using this type of solution, allow it to sit for 10 to 15 minutes before pouring into the bag. Settling the formula will reduce the chance of sounding an alarm due to air in the tubing.
2. Remove the protective cover from the barbed adapter. If using a pole clamp, place the protective cover in the groove on the back of the clamp.
   NOTE: Remove all air from the bag and tubing if using with a carry pack. Continue to Step 3 for instructions on removing air. If the set hangs above the pump on an IV pole, you may skip to Step 4.
3. Turn the bag upside down and gently squeeze. Tilt bag as needed to evacuate air through tubing port.
4. Gently pinch the teal-colored tubing below the drop symbol. Hold this position until the air dissipates from the tubing. Gently squeeze bag at the same time to assist fluid flow. If the fluid does not flow, pinch pressure may be too strong.
   NOTE: Inside the teal-colored tubing, below the water drop symbol is the in-line occluder. The in-line occluder has an anti-free-flow valve. By pinching the tubing gently, the tubing moves away from the in-line occluder allowing fluid to flow. It is important only to pinch the tubing below the water drop symbol to avoid damaging the in-line occluder.
   NOTE: Be extremely careful to pinch tubing using only the flat, soft part of your finger. Do not use fingernails when pinching tubing; doing so may puncture the delivery set. If you suspect a punctured delivery set, please discard it and use a new set.
   NOTE: Air may also be removed from the tubing using the primer pump feature. 
5. Loop silicone tubing around the pump wheel, stretching it lightly. Seat the cassette into the pump. Close the pump door.
   NOTE: When using the 1200ml set with the Mini Backpack, load the set into the back section of the pack and thread the cassette through the port in the bottom corner of the pack before loading the cassette into the pump.
6. To turn the pump on, press and hold the ON/OFF key for 1.5. While the pump runs through a self-test, the display will light and an audible alarm will sound as the pump displays the nine-digit serial number three digits at a time for one second each. The display will then show the letter ‘R’ followed by a number, which is the software revision. Next, all segments of the display will show for 2 seconds. Verify that all display segments and symbols are active. The self-test is complete and the pump will then display the last programmed rate and will be in pause mode. If any air is still in the tubing, continue to Step 7 to use the prime pump feature
7. Press and hold the PRIME key. The alarm will sound once and the pump will begin pumping at the maximum rate of 600 ml/hr. The display will read “TO STOP LET GO.” Once all air is removed from the tubing, release the key. The pump will stop, the display will revert to the last programmed rate, and the pump will be in pause mode.

Cautions:

• It is important to keep the air sensor free of debris including spilled fluids or food that may adhere to the sensor and prevent detection of air in the tubing.
• Use a cotton swab to clean the pathways of the cassette receptacle. (Refer to the Operator’s Manual for further cleaning instructions).
• When using a programmed dose, infinite dose, or interval feeding setting, the volume of food in the bag/bottle should be monitored throughout the feeding cycle to ensure the appropriate dose has been received by the patient.

How to clean Moog EnteraLite Infinity Enteral Feeding Pump?

• Clean the pump with warm soapy water (standard dish soap) and a nonabrasive sponge or soft cloth. Use a cotton swab to clean the pathways of the cassette receptacle and to remove teal silicone residue from the pump wheel roller pins.
• OR Apply one of the following solutions for approximately 10 minutes, then wipe the pump clean with a damp cloth or sponge
  - 5% bleach and water solution
  - Multipurpose household disinfectant cleaner
• Rinse the pump by holding it under a stream of warm water. Then, dry with a clean cloth
• NOTE: Avoid harsh cleaners/disinfectants. They may cause damage to pump surfaces and may affect pump functionality. Moog has tested the following disinfectants for acceptability for cleaning and disinfecting the EnteraLite Infinity pump.
• Moog EnteraLite Infinity Enteral Feeding Pump - User Manual

Specification

Customer Reviews